Open: 24 hours
Address: 76 Ashford, Irvine, CA 92618
© 2025 Urgent Garage Doors Inc
Roller Replacement in Orange County, CA
Worn or metal rollers create grinding, rattling, and track wear. Urgent Garage Doors replaces noisy wheels with sealed-bearing nylon “quiet” rollers sized to your door, aligns tracks, and tunes your opener so the system runs smooth, quiet, and within spec.
✓ Hardware life: Less shock on hinges, tracks, and opener gears.
✓ Coastal-smart: Corrosion-resistant stems/bearings for OC marine air.
✓ Noise down: Nylon tread + sealed bearings slash squeal and vibration.
✓ Smoother travel: Proper stem length and wheel centering reduce chatter.
✓ Hardware life
✓ Coastal-smart
✓ Noise down
✓ Smoother travel
What our Clients think about us
Your satisfaction is our priority.
Why Choose Urgent Garage Doors
One accountable team: Inspect → align → replace → tune in one visit.
Every configuration: Standard, low-headroom, high-lift, wind-reinforced, and full-view doors.
Door-first approach: We balance springs and set opener limits so rollers glide, not grind.
Quality parts: 10–13 ball sealed nylon rollers matched to weight/cycles; stainless stems available.
Immediate Actions (What to Do Now)
Note where the noise peaks (start/stop, corners, mid-travel).
Snap photos of rollers, hinges, and tracks (inside jambs).
Tell us your door size/material (single/double; insulated steel/wood/glass).
Call our team—we’ll spec the correct roller (2" residential or 3" commercial) and schedule a quick service window.
Common Scenarios We Handle
Squeals/rattles and thumping from flat-spotted wheels
Track scarring or rollers that wobble/pop at section joints
Coastal corrosion seizing bearings/stems
Heavy insulated or glass doors needing higher-spec rollers
Low-headroom/high-lift systems with geometry-specific needs
Safety & Site Control
Clamp door, de-energize opener, verify spring balance and sensors; protect floors/vehicles.
Assessment & Measurements
Confirm roller diameter/stem length, hinge numbers (#1–#5), track geometry, and door weight; document with photos.
Removal & Prep
Replace rollers section by section; clean tracks, check fasteners, true verticals/horizontals/back-hangs.
Install Premium Nylon Rollers
Fit sealed-bearing nylon rollers (10–13 ball); verify free spin, centered wheel, correct stem engagement—no wobble.
Align, Lube & Torque
Fine-align tracks; torque hinge/track fasteners; apply targeted garage-grade lube to pivots (never greasing the track).
Tune & Walkthrough
Set opener travel/force, multi-cycle test, review care; leave a parts list and maintenance tips.
What’s Included
Roller spec & measurement (diameter, stem, load)
Premium sealed-bearing nylon rollers (qty matched to door)
Track inspection & alignment (toe-in/back-hang)
Fastener torque & hinge check (#1–#5)
Targeted lubrication (pivots only)
Final tune & safety check (UL 325 sensors, force/travel)
Costs & Timelines (What to Expect)
Typical duration: 30–60 minutes single; 45–90 minutes double; add time for track/hinge corrections.
Key cost drivers: Door size/weight, roller grade (10 vs. 13 ball; stainless stems), track/hinge condition, special lift geometry.
Estimate clarity: Line items for rollers, any hinge/track fixes, and installation/tune.
Insurance & Claims Help
Usually an owner-elected upgrade. If replacing due to impact or corrosion following a covered event, we’ll provide photos, specs, and invoice details for your records.
(Coverage varies by policy; not financial advice.)
Risks of Waiting (Why Act Now)
Bearing seizure → gouged tracks, popped rollers
Opener strain and premature gear/belt wear
Panel/hinge fatigue from vibration and misalignment
Escalating noise that loosens more hardware over time
Methods, Materials & Quality Standards
Rollers: Nylon tread, sealed 6200-series bearings, 10–13 ball; load-rated per door.
Stems: Zinc-plated or stainless for coastal installs; correct length to center wheel in track.
Tracks: Plumb/level/toe-in verified; back-hang angles set to prevent chatter.
Hinges: Inspect for cracks/ovalized holes; replace as needed; reinforce wide doors with struts.
Lube: Silicone/PTFE garage-grade—thin film on pivots; no grease in tracks.
Compliance: UL 325 sensor test; opener force within spec; document changes.
Frequently Asked Questions
Are nylon rollers really quieter than metal?
Yes—nylon + sealed bearings cut metal-on-metal noise and vibration dramatically.
Do I need to replace tracks too?
Not usually. We clean/true tracks; only bent/corroded sections need replacement.
How long do nylon rollers last?
High-quality sealed rollers are high-cycle; lifespan depends on door weight, alignment, and environment.
Will lubrication still be needed?
A light, periodic pivot lube helps longevity; we avoid greasing tracks to keep grit out.
Good for coastal homes?
Yes—ask for stainless stems and sealed bearings; we include care tips for salt air.
Can you do this with low headroom?
Absolutely—we carry long-stem and low-headroom-friendly options and adjust geometry accordingly.
More Urgent Garage Doors Repair Services
Proudly Serving All of Orange County
Address: 76 Ashford, Irvine, CA 92618
Phone: (949) 529-7743
Hours: Open 24 hours
Email: office@urgentgaragedoors.com
Urgent Garage Doors is Irvine-based and available 24/7 for residential and commercial service across Orange County. We provide new garage door installation, smart opener setup, broken spring replacement, off-track door repair, cable & roller replacement, panel swaps, sensor fixes, and full opener repair & maintenance—fast, professional, and backed by warranty.
Proudly serving Irvine, Anaheim, Santa Ana, Orange, Tustin, Costa Mesa, Newport Beach, Huntington Beach, Mission Viejo, Lake Forest, Fullerton, Yorba Linda, Laguna Beach, Dana Point, San Clemente, and surrounding neighborhoods.
Let’s start a conversation
Book Your Free Consultation call Now
Contact us:
CALL (949) 529-7743
Hours: Open 24 hours
76 Ashford, Irvine, CA 92618