Open: 24 hours
Address: 76 Ashford, Irvine, CA 92618
© 2025 Urgent Garage Doors Inc
Track Repair, Realignment & Replacement in Orange County, CA
Bent, misaligned, or corroded garage door tracks cause binding, scraping, derailments, and noise. Urgent Garage Doors repairs dents, re-squares and re-hangs tracks, or replaces damaged sections with the correct radius and gauge—then balances and tunes your system so the door runs smooth, level, and within spec.
✓ Clean clearances: Even reveals for quiet, centered roller travel.
✓ System tune: Balance, force/limit set, and safety checks included.
✓ True & square: Proper plumb, level, toe-in, and back-hang angles.
✓ Right hardware: Correct radius/gauge and corrosion-smart fasteners.
✓ Clean clearances
✓ System tune
✓ True & square
✓ Right hardware
What our Clients think about us
Your satisfaction is our priority.
What Is Track Repair, Realignment & Replacement?
A service that restores the path your rollers follow.
We correct plumb, level, toe-in, and back-hang geometry; remove dents or kinks; and when needed, install new track sections with the correct radius (12", 15", etc.), gauge, and mounting pattern. We finish with alignment, balance, and opener tuning.
Why Choose Urgent Garage Doors
One accountable team: Stabilize → diagnose → repair/replace → align → tune in one visit.
Every configuration: Standard-lift, low-headroom, high-lift, and full-view setups.
Door-first approach: We verify roller/hinge health and spring balance so tracks stay true.
Coastal-smart: Galvanized/powder-coated tracks and stainless/galv. fasteners for OC marine air.
Immediate Actions (What to Do Now)
If the door rubs or sticks, stop operating—forcing it can bend panels or pop rollers.
Note where the rub marks, dents, or daylight gaps appear.
Snap photos of the verticals, curve (radius), and horizontals/back-hangs.
Call our dispatcher—we’ll stabilize, assess, and repair or replace safely.
Common Scenarios We Handle
Vehicle bump that creased vertical track or shifted brackets
Door pops/wobbles at the curve; rollers climbing flanges
Persistent rubbing or daylight gaps from out-of-square framing
Corroded or pitted tracks near the coast snagging rollers
Low-headroom chatter from wrong back-hang angle or poor toe-in
Safety & Stabilization
Secure door, unplug opener, protect floors/vehicles; set exclusion zone.
Diagnosis & Mapping
Check plumb/level, measure reveal at jambs, inspect roller stems/hinge offsets (#1–#5), and verify radius type and back-hang geometry.
Repair or Replace Plan
Decide between true/straighten (minor dents, bracket shift) vs. section replacement (kinks, creases, corrosion). Select correct radius/gauge.
Professional Repair/Replacement
Realign verticals/horizontals; correct toe-in; set back-hang heights/angles; replace damaged sections; use corrosion-appropriate fasteners into structure.
Roller & Hardware Check
Inspect/replace rollers as needed; verify hinge integrity; ensure wheels run centered with no flange contact.
Balance, Tune & Test
Confirm spring balance and set opener travel/force; multi-cycle test for quiet, centered travel; verify UL 325 safety sensors.
What’s Included
Alignment survey & photos (plumb/level/reveal)
Track true/repair or track section replacement (correct radius/gauge)
Back-hang and bracket reset into structural members
Roller/hinge inspection; nylon roller swap quoted if indicated
Spring balance & opener tune (limits/force) + UL 325 checks
Documentation (what was corrected/replaced; future maintenance tips)
Costs & Timelines (What to Expect)
Typical duration: 45–90 minutes for realignment/spot repair; 60–120+ minutes for section replacements or low-headroom/high-lift rigs.
Key cost drivers: Extent of damage, replacement length (vertical/curve/horizontal), radius/gauge, hardware condition, and coastal upgrades.
Estimate clarity: Line items for track sections/fasteners, labor, and any rollers/hinges/back-hang parts.
Insurance & Claims Help
After impact or storm, we can supply before/after photos, measurements, and a concise narrative for your records/adjuster.
(Coverage varies by policy; not financial advice.)
Risks of Waiting (Why Act Now)
Roller derailment and panel/hinge damage
Opener strain from binding tracks
Noisy operation loosening more fasteners over time
Accelerated cable/drum wear from uneven travel
Methods, Materials & Quality Standards
Tracks: Correct radius (12", 15", high-lift/vertical) and gauge; straight, burr-free flanges.
Alignment: Plumb verticals; level horizontals; precise toe-in; back-hangs set to eliminate chatter.
Anchorage: Brackets fastened to framing, not thin skin; use stainless/galv. hardware for coastal installs.
Compatibility: Verify with hinge offsets and roller stems; preserve sightlines on full-view doors.
Integration: Pair with nylon rollers and reinforcement struts where flex was causing rub.
Compliance: UL 325 safety verification; opener force within manufacturer spec.
Frequently Asked Questions
Can you straighten a bent track, or does it need replacing?
Minor dents/shift can be trued. Kinks/creases or corrosion usually merit replacement for safety and longevity.
Why does my door rub only at the curve?
Often incorrect radius alignment, toe-in, or back-hang height. We reset geometry and verify roller/hinge compatibility.
Will new tracks make it quieter?
When aligned with nylon rollers and correct toe-in, most doors become noticeably quieter.
What if my framing is out of square?
We can shim and anchor into structure to restore reveals and smooth travel.
Do you service low-headroom/high-lift systems?
Yes—geometry is critical there; we carry profile-compatible tracks and hardware.
Will you tune my opener after?
Absolutely —travel/force settings are part of every track service, plus UL 325 checks.
More Urgent Garage Doors Repair Services
Proudly Serving All of Orange County
Address: 76 Ashford, Irvine, CA 92618
Phone: (949) 529-7743
Hours: Open 24 hours
Email: office@urgentgaragedoors.com
Urgent Garage Doors is Irvine-based and available 24/7 for residential and commercial service across Orange County. We provide new garage door installation, smart opener setup, broken spring replacement, off-track door repair, cable & roller replacement, panel swaps, sensor fixes, and full opener repair & maintenance—fast, professional, and backed by warranty.
Proudly serving Irvine, Anaheim, Santa Ana, Orange, Tustin, Costa Mesa, Newport Beach, Huntington Beach, Mission Viejo, Lake Forest, Fullerton, Yorba Linda, Laguna Beach, Dana Point, San Clemente, and surrounding neighborhoods.
Let’s start a conversation
Book Your Free Consultation call Now
Contact us:
CALL (949) 529-7743
Hours: Open 24 hours
76 Ashford, Irvine, CA 92618